You are here: SUKMA Tirta Persada - Distributor Pompa Air»Industry Pumps

Industry Pumps

Industry Pumps

KSB Mega CPK-Horizontal radially split volute casing pump

Design

KSB Mega CPK
Horizontal, radially split volute casing pump in back pull-out design to EN 22 858 / ISO 2858 / ISO 5199, single-stage, single-entry, with radial impeller. Also available as variant with “wet” shaft. ATEX-compliant version available.

KSB-Mega CPK

▪ Volute casing pump

▪ Horizontal installation

▪ Back pull-out design

▪ Single-stage

▪ Meets the technical requirements to ISO 5199

▪ Dimensions and ratings to ISO 2858 complemented by pumps of nominal diameters DN 25, DN 200 and above

 

Pump casing

▪ Single or double volute, depending on the pump size
▪ Radially split volute casing
▪ Volute casing with integrally cast pump feet
▪ Replaceable casing wear rings (as required)
Impeller type
▪ Closed radial impeller with multiply curved vanes
Shaft seal
▪ Gland packing
▪ Commercial single and double mechanical seals
▪ Commercial cartridge seals
▪ Shaft fitted with a replaceable shaft protecting sleeve in the shaft seal area
Alternative:
▪ Version without shaft protecting sleeve with “wet shaft” (in Europe and
Northern Asia only)
Bearings
Bearings:
▪ Medium-duty
– Radial bearing: cylindrical roller bearing
– Fixed bearing: paired angular contact ball bearings / double-row angular
contact ball bearing
▪ Economy
– Floating bearing assembly: deep groove ball bearings
Lubrication:
▪ Oil lubrication
▪ Grease lubrication

Applications

Handling of aggressive liquids in the chemical and petrochemical
industries as well as in refinery

Overview of technical data

KSB-Mega CPK Configuration
Type of impeller Closed / Radial
Type of installation Long- coupled
Maximum drive rating 90 kW
Impeller material (EN standard) 1. 4593 / 1.4517 / A995GRCD4MC;GP240GH+N/ A216GRWCB;JL1040/ A48CL35
Type of bearing Ball bearings
Drive frequency 50 Hz / 60 Hz
Maximum speed of rotation 4 1/min
Maximum flow rate 1. 160 m³/h
Maximum discharge-side pressure 25 bar
Casing material (EN standard) DUPLEX STAINLESS STEEL 1. 4593/;GREY CAST IRON JL1040 / A48CL3;STAINLESS STEEL 1.4408 / A743;STEEL GP240GH+N/ A216 GR WCB
No. of impeller entries Single entry
Integrated control system Yes
Minimum flow rate 2 m³/h
Suction characteristics Non- priming
Drive voltage Low voltage
Pull-out design Yes
Pump set location Dry installed
Heatable Yes
Max. permissible fluid temperature 400 °C
Main applications Industry and process engineering; Oil / Gas
Type of casing Volute casing
Type of connection Flange
Type of lubrication Grease / Product lubrication
Type of drive Electric motor
Installation position Horizontal
Level indication Grease lubrication
Shaft material (EN standard) ALLOY STEEL 1. 7709+QT+SR;DUPLEX STAINLESS STEEL 1.4462;STEEL C45+N
Type of coupling Direct
Shaft seal type Gland packing; Mechanical seal
Maximum head 162, 00 m
Maximum rated pressure (discharge) PN25
Minimum head 2, 00 m
Nozzle position End suction
Casing partition Radially split

 

EBARA                    GRUNDFOS                     KSB             

EBARA-EVM - VERTICAL MULTI-STAGE STAINLESS STEEL PUMPS

EBARA-EVM – VERTICAL MULTI-STAGE STAINLESS STEEL PUMPS

APPLICATIONS

Ebara-EVM-Series• Civil, Industrial, farming, fire-fighting, boosting systems
• Water treatment plants (reverse osmosis, filtrations)
• Irrigation system
• Washing system
• Movement of hot and cold water for heating, cooling and air-conditioning system.
• Boiler feeding
• Movement of moderately aggressive chemical liquids without solids.

Water treatment

• reverse osmosis systems
• distillation systems
• filtration
• light chemical applications;

 

Industrial washing systems

• car washing, bottle and glassware washing,
parts washing, crate washing, washing and
finishing of metal parts, vegetable washers, and
seafood washing applications
• fire-fighting systems;

Heating and conditioning

• hot water circulation
• cooling systems
• industrial boilers;
Water supply
and pressurization
• pressure boosting
• machine tools;
Agriculture and irrigation

• field irrigation
• sprinkler irrigation
• drip irrigation.

MATERIALS

Ebara-EVM• Impeller, diffusers, casing cover, outer casing, shaft sleeve, coupling covers,
fixing in contact with liquid: AISI 304 stainless steel
• Bottom casing: AISI 304 stainless steel (EVM) – cast iron (EVMG),
AISI 316L (EVML)
• Motor bracket and base: cast iron (not in contact with the pumped liquid)
• Bearings (in contact with liquid): tungsten carbide
• Mechanical seal: Silicon carbide/carbon/Viton
• Shaft: AISI 316 stainless steel
• Tie rods and fixings not contact with liquid: zinc coated stainless steel

CARTRIDGE SHAFT SEAL

EVM 32-45-64 pumps mount the carridge shaft seal
All components of a cartridge shaft seal constitute a sole part on a shaft sleeve. The cartridge mechanical seal is ready to
be installed between pump shaft and motor shaft. The most important benefits of this kind of seal are:
• Easy to install
• Protected seal faces
• Safe and easy handling
We are at disposal for evaluating your specifications and needs in order to find the best solution for your plants and
applications.

MOTORS

• Pumps configured for the installation of a standard IEC motor
• Pumps suitable for different motor types: explosion proof, high efficiency, low noise and with integrated inverter
(EVM VS)
• 50 – 60 Hz
• 2 – 4 poles
• Motors with various voltages and frequencies
• Motors conforming to UL/CSA standards on request.

 

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

Wilo-JP series-Centrifugal Sanitary Pumps

Product Introduction

Wilo-JP series-Centrifugal Sanitary Pumps in all sectors of beverage and food processing industries,

JP series, special feature with unique spiral-shaped casing and the double curved impeller design for high efficiencyhave proven successfully by absolute reliability such as low energy consumption,

perfect CIP and low noise level.

 

Features / Benefits

Wilo-JP-DIMIdeal for hygienic application of dairy, food, beverage,
pharmaceutical and other industries
Unique spiral-shaped casing for high efficiency
Designed for either CIP or easy manual cleaning
Low NPSH requirement, power consumption, noise level
Up to 100m³/hr flow rate, 80m head
SS316L for all wetted parts & EPDM standard
Single seal standard & easy change to double seal

Wilo-JP-Curves

 

 

 

 

 

 

 

 

 

 

 

 

 

Wilo-JP-Material

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

Tsurumi - BX submersible pump Explosion proof

 

Tsurumi – BX submersible pump Explosion proof

The BX-series is the explosion–proof type of the B-series and is available for operating in an area in which an explosive atmosphere occurs occasionally. The pump conforms to the relevant EU directives and is certified by ATEX II 2 G Ex d IIB T4 standard.

 

Application

  1. Transferring sewage and wastewater to wastewater treatment plant
  2. Dewatering wastewater from industrial plant (e.g. petrochemical plant, etc)
  3. Pumping wastewater from collection sump where explosive atmosphere is likely to present

 

 Impeller

Tsurumi-BX Series-ImpellerFlame proof according to ATEX An impeller having a wide channel extending from inlet to exit,

which prevents internal clogging by

solids sucked in via the inlet.

 

Classification

Tsurumi BX-explosion-proof-sewage-pumpsElectric submersible pump
Explosion proof according to ATEX 94/9/EC
II 2G Ex d II B T4.
Channel impeller
Impeller passage 47mmx53mm
Suitable for waste water and liquids carrying
waste and solid matters

 

Electric Motor

Dry-type submersible induction motor,
Insulation class F, 4 poles, 1420 r.p.m.
Direct on line start
Voltage: 400V, 50Hz, 3-phase
Power input: 3,00kW
Power output: 2,30kW
Nominal current: 5,4A
Start current: 33,1A
Electric Cable
10m H07RN6GX1,5mm2
Motor Protection
Miniature protector in windings
(snap-action bi-metal device)
Shaft Seal
Double mechanical seal in oil bath
additional lubrication by oil lifting device
Primary Seal:
silicon carbide on silicon carbide
Secondary Seal:
ceramic on carbon

 

Bearings

Shielded ball bearings, maintenance-free

Material

ø Discharge bore mm

80mm,100mm
Pumping Fluid Temperature
0-40°C
Type of Fluid
Municipal sewage
Pump Compo- nents Impeller
Non-clog impeller
Shaft Seal
Double mechanical seal
Bearings
Shielded ball bearings
Material Impeller
Grey iron casting EN-GJL-200
Casing
Grey iron casting EN-GJL-200
Suction Plate
Grey iron casting EN-GJL-200
Shaft Seal
Silicon carbide in oil bath
Motor Type, Poles
Induction motor, 2 poles, 
IP68, Induction motor, 4 poles, IP68
Lubrication
Turbine oil (ISO VG32)
Insulation
Insulation class F
Motor Protector (built-in)
Circle thermal cut-out
Phase / Voltage
3-phase / 400V / 50Hz / d.o.l.
Material Casing
Grey iron casting EN-GJL-200
Shaft
Stainless steel EN-X30Cr13
Cable
Rubber, 10m H07RN6G
Discharge Connection
Inside thread, JIS10K flange
Optional Accessories
Guide rail fitting "TOS" 
(guide support, duck foot bend,
 lifting chain)
/Bend and stand set for free standing types

 EBARA               GRUNDFOS              KSB         TSURUMI         WILO

Tsurumi - SFQ Series Corrosion resistant pumps

 

 

 

Tsurumi – SFQ Series

 

 

Tsurumi corrosion resistant pumps are available in 316 or 304 stainless steel (SFQ Series, SQ Series) as well as titanium (TM Series). Featuring semi-vortex, vortex, and semi-open impellers, our solidly engineered pumps can endure the corrosive forces of your toughest applications

 

Dimensions in mm:

Tsurumi-SQF

 

Stainless steel pump – The SFQ pump has been developed exclusively for corrosive liquids. Applying austenitic steel in all wetted parts, the SFQ pump is a highly specialised pump in terms of design and materials

 

Performance curves

K40_1_1

 

 

 

 

 

 

 

 

 

Material

ø Discharge bore mm 50mm, 80mm
Pumping Fluid Temperature 0-40°C
Type of Fluid Aggressive sewage
Pump Compo- nents Impeller Open type impeller
Shaft Seal Double mechanical seal
Bearings Shielded ball bearings
Material Impeller Stainless steel casting DIN GX5CrNiMo19-11-2
Casing Stainless steel casting DIN GX5CrNiMo19-11-2
Suction Plate Stainless steel casting DIN GX5CrNiMo19-11-2
Shaft Seal Silicon carbide in oil bath
Motor Type, Poles Induction motor, 2 poles, IP68
Lubrication Turbine oil (ISO VG32)
Insulation Insulation class E, Insulation class F
Motor Protector (built-in) Circle thermal cut-out
Phase / Voltage 3-phase / 400V / 50Hz / d.o.l., 3-phase / 400V / 50Hz / s.d.
Material Casing Stainless steel casting DIN GX5CrNiMo19-11-2
Shaft Stainless steel EN-X5CrNiMo17-12-2
Cable Rubber, 10m H07RN-F
Discharge Connection Inside thread, JIS10K flange

Dimensions – guide rail fitting type in mm

Tsurumi-SQF-diam

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EBARA            GRUNDFOS             KSB            WILO           TSURUMI

 

KSB - Etanorm GPV / CPV Single-stage volute casing pump,for vertical installation in closed tanks under atmospheric pressure

Design

KSB – Etanorm GPV / CPV
Single-stage volute casing pump, ratings to EN 733, for vertical installation in closed tanks under atmospheric pressure. Up to an immersion depth of 2000 mm.

 

Applications

Handling of neutral degreasing and phosphatizing solutions, wash water with degreasing agents, dipping paints, etc.

 

 KSB-Etanorm GPV-W-CPV-W-modularSectional drawing

1 Motor housing 2, 3 Rolling element bearings
4 Motor stool 5 Cover plate
6 Shaft 7 Overflow opening
8 Intermediate pipe 9 Shaft passage
10 Casing cover 11 Impeller
12 Suction nozzle 13 Discharge nozzle
14 Riser 15 Volute casing
16 Clearance gap

 

 

 

 

 

 

 

 

 

 

 

To transport the pump/pump set suspend it from the lifting tackle as shown below.

KSB-Etanorm GPV-W-CPV-W.dia

 

 

 

Fig. 1: Transporting the pump set without/with cover plate up to motor size 160

 

KSB-Etanorm GPV-W-CPV-W-hor

 

Fig. 2: Transporting the pump set without/with cover plate up to motor size 160 for
larger installation depths

 

Overview of technical data

Type of bearing Rolling element bearings
Casing partition Radially split
Drive frequency 50 Hz / 60 Hz
Type of drive Electric motor
Drive voltage Low voltage
No. of impeller entries Single entry
Maximum submergence 535 mm
Impeller material (EN standard) 1. 4408;JL 1040
Type of coupling Direct
Type of lubrication Grease lubrication
Max. permissible fluid temperature 70 °C
Nozzle position Variable
Maximum rated pressure (discharge) PN 10; PN 16
Pump set location Wet well
Shaft material (EN standard) 1. 4462;C45+N
Standard EN 733
Suction characteristics Non- priming
Top plate Yes
Type of casing Volute casing
Type of impeller Radial; Closed
Type of connection Flange
Casing material (EN standard) 1. 4408;JL 1040
eClass assignment 36410101; 03641000;36410100
Maximum head 100, 00 m
Minimum head 1, 50 m
Installation position Vertical
Shaft seal type Shaft seal ring
Main applications Industry and process engineering; Waste water / sewage
Casing material Cast iron; Stainless steel
Maximum discharge-side pressure 10 bar
Maximum drive rating 90 kW
Type of installation Stationary
Maximum flow rate 750 m³/h
Minimum flow rate 3 m³/h
Maximum speed of rotation 3. 500 1/min

 

 

EBARA            GRUNDFOS             KSB            WILO           TSURUMI

KSB-Etaseco Seal-less volute casing pump in back pull-out design with fully

 

 

Design

KSB-Etaseco Horizontal / vertical, seal-less volute casing pump in back pull-out design with fully enclosed canned motor

KSB-etaseco-mudular copyLow noise emission, with radial impeller, singlestage, single-entry, pump casing connecting dimensions to EN 733.

 

 

 

 
Applications

Handling of aggressive, flammable, toxic, volatile, or valuable liquids in the chemical and petrochemical industry, in environmental engineering and the general industry.

 

Drive

KSB-Etaseco-CurvesThree-phase, asynchronous canned motor, enclosure IP 55,
without explosionproof status. Thermal motor protection by
means of PTC thermistors. The motor design is in accordance
with IEC 60 034 (DIN VDE 0530).

 

 

 

 

 

Overview of technical data

Type of bearing Plain bearings
Casing partition Radially split
Drive IEC standardized motor
Drive frequency 50 Hz / 60 Hz
Type of drive Electric motor
Drive voltage Low voltage
Connection to power supply 220/ 400/690 V, 3~
No. of impeller entries Single entry
Impeller material (EN standard) JL1040; JS1025
Type of installation Close- coupled
Type of coupling Direct
Type of lubrication Oil / Product lubrication
Max. permissible fluid temperature 140 °C
Nozzle position End suction
Maximum rated pressure (discharge) PN 16
Pull-out design Yes
Pump set location Dry installed
Shaft material (EN standard) 1. 4021
Suction characteristics Non- priming
Type of casing Volute casing
Type of impeller Multi- vane impeller;Closed;Closed / Radial;Radial
Type of connection Flange
Casing material (EN standard) JS1025; JL1040
eClass assignment 36410100; 36410101;36410000
Maximum head 100, 00 m
Minimum head 9, 00 m
Installation position Horizontal or vertical
Shaft seal type Canned motor pump
Main applications Industry and process engineering
Casing material Cast iron; Nodular cast iron
Maximum discharge-side pressure 16 bar
Maximum drive rating 18 kW
Type of installation Stationary
Maximum flow rate 250 m³/h
Minimum flow rate 3 m³/h
Maximum speed of rotation 3. 500 1/min

 

EBARA            GRUNDFOS             KSB            WILO           TSURUMI

WILO-CP 80-150W Submersible Contractor pump raised suction strainer and Inox design.

 

WILO-CP 80-150W – Submersible Contractor pump

Design

Wilo-CP_80-150W_curveSubmersible Contractor pump with top discharge; raised suction strainer and Inox design.

 

 

 

 

Application

  • civil engineering, drainage of tunnels and excavation pits
  • dewatering of fluids containing solid sediments
  • mobile use for contractors in service industries

 

Special features / product benefits

  • double housing water-cooled motor for flat suction
  • light weight
  • high quality silicon carbide double mechanical seal
  • high-efficient and wear-resistant HCR (high chrome) impeller
  • integrated motor control for current overload and high temperature

 

Technical data

  • discharge diameter DN80~ DN150
  • solid passage 10 mm
  • motor power 1.5kW~7.5kW; 2pole
  • 1~230V and 3~400V

 

EBARA            GRUNDFOS            KSB            WILO          TSURUMI

KSB - HGM-RO High-pressure pumps for reverse osmosis systems

 

 

KSB-HGM-RO high-pressure pump – reliable drinking water treatment in reverse osmosis systems

KSB_HGM_RO-modular

 

Drinking water production in RO systems requires a high-pressure pump of top reliability which provides continuously economical operation. KSB responds to this need with an ideal solution: the HGM-RO high-pressure pump.

 

 

 

 

 

 

High-pressure pumps  HGM-RO High-pressure pumps for reverse osmosis systems need to be able to handle the harsh conditions which prevail in seawater desalination plants.

KSB-HGM-RO-Curves

 

KSB has opted for radially split high-pressure pumps.

Their radially split design makes HGM-RO high-pressure pumps particularly robust, enabling them to cope with the extreme conditions of drinking water treatment in seawater desalination.

 

 

 

Benefits of using KSB’s radially split high-pressure pumps in reverse osmosis systems:

HGM-RO-Radially-split-designMinimum energy input, low operating costs

Excellent NPSH value thanks to axial inflow with suction stage impeller. Continuously high efficiencies.

 

Compact design

Internal, product-lubricated plain bearings with a short bearing span ensure smooth running and therefore high pump availability and reliability as well as a long service life of wear parts.

 

Corrosion-resistant design

The HGM-RO high-pressure pump is made of duplex or super duplex stainless steels. Its corrosion-resistant design (e.g. dry shaft) translates into a long service life.

KSB-HGM-RO-01k

Low monitoring requirements

There is no need for an additional lubrication system, and the pump does not require any vibration or bearing temperature monitoring. This saves both initial and operating costs for the pump set.

Minimum maintenance costs

Because of its axial inlet, the HGM-RO high-pressure pump has just one mechanical seal, which minimises spare parts costs. The ring section design ensures top reliability in the extreme conditions of reverse osmosis systems. No lubrication systems are required. The mechanical seal is easy to replace.

Reduced construction costs

The pump’s compact design, low weight and smooth running lower the requirements to be met by the foundation. Flexible connection branches facilitate connection to the system piping.

 

Easier to install and dismantle than axially split pumps

The pump can be dismantled and reassembled from either side. The wear parts are easily accessible.

 

EBARA            GRUNDFOS            KSB            WILO          TSURUMI

Ebara - SAL Slurry Pumps

 

 

FEATURES

Ebara-SAL• No power overload
Specially designed impeller with a limit load
feature is used so that there is never a power overload no matter what the head.

• Low energy consumption and yet highly efficient
Unique hydraulic design makes this pump more efficient than any other type.
The initial rate of efficiency is sustained for reducing electrical power consumption.

• Highly durable
A special, wear-resistant iron casting is used for both body and impeller.

• Ample motor output allowance
The motor has ample power output allowance. It will operate without change of output with mixed solution of 1.1 specific gravity.

• Minimal gland packing leakage
Rear impeller vane ensures minimal leakage from durable gland packing.

• Corrosion and wear-resistant materials
Both chrome iron casting and two-phase stainless steel are available. Interchangeability makes a wide range of
applications possible

 

ABOUT WEAR AND CORROSION RESISTANCE

Ebara-SAL-CurvesThe impellers, which are subject to the greatest possibility of
wear, are of tough high chrome cast iron about 20 times as
wear resistant as ordinary cast iron.

• The casing, which is subject to less possibility of wear, is of
less expensive low chrome cast iron with three to five times
the wear resistance of ordinary cast iron

 

Note:

Ebara-SAL-dim1. Motor specifications: Three-phase induction
motor; open, drip-proof type : D.P.; completely
sealed external fan type : T.E.
2. Dimensions marked with an asterix (*) will
change when using a completely sealed
external fan type motor with four poles of 15kW
or six poles of less than 11kW.
3. The pump must never be allowed to rotate in
reverse. Confirm test in operation of motor only
that rotation direction is correct

 

 

 

 

Application

Chemical Industry

  • -Neutralizing agents (milk of lime)
  • -Filter press suply liquid
  • (water with high mud concentration)
  • -Wet type dust collection
  • (dust-impregnated water)
  • -Sediment disposal (drains)

Oil Refining

  • -Waste disposal
  • (non corroded waste)
  • -Pit drain
  • (water with soft mud)

Paper & Pulp

  • -Pulp treatment (max. 4% concentration)
  • -Additives (clay-mixed water)
  • -Neutralizing agents (milk of lime)
  • -Waste disposal (sedimen-mixed water)

Food

  • -Kitchen darins (filtrate)
  • -Waste liquid disposal

Sugar / Salt Manufacturing

  • -Used wash water
  • (earth and sand-mixed water)
  • -Steamed and boiled liquid
  • (molasses)

Steel Manufacturing & Refineries

  • -Used coke cooling water
  • (mixed with coke dust)
  • -Casting sand recovery
  • (water mixed with sand)
  • -Conveyor pit drainage
  • (water mixed with iron oxide)
  • -Residual settling tank liquid
  • (water mixed with sludge)
  • -Dust collecting circulating liquid
  • (dust mixed water)

Thermal Power Stations

  • -Incinerator ash disposal
  • (water mixed with ash, carbon)
  • -dust disposal
  • (dust mixed water)

More application Ebara-SAL

 

EBARA            GRUNDFOS            KSB            WILO          TSURUMI

Pages:123456789Next »