You are here: Distributor Pompa Air»Products Overview

Warning: Illegal string offset 'b_cats' in /home/dis10007/public_html/wp-content/themes/InnovationScience2/blog.php on line 43

Warning: Illegal string offset 'b_excats' in /home/dis10007/public_html/wp-content/themes/InnovationScience2/blog.php on line 44

Warning: Illegal string offset 'b_layout' in /home/dis10007/public_html/wp-content/themes/InnovationScience2/blog.php on line 45

Products Overview

KSB Mega CPK-Horizontal radially split volute casing pump

Design

KSB Mega CPK
Horizontal, radially split volute casing pump in back pull-out design to EN 22 858 / ISO 2858 / ISO 5199, single-stage, single-entry, with radial impeller. Also available as variant with “wet” shaft. ATEX-compliant version available.

KSB-Mega CPK

▪ Volute casing pump

▪ Horizontal installation

▪ Back pull-out design

▪ Single-stage

▪ Meets the technical requirements to ISO 5199

▪ Dimensions and ratings to ISO 2858 complemented by pumps of nominal diameters DN 25, DN 200 and above

 

Pump casing

▪ Single or double volute, depending on the pump size
▪ Radially split volute casing
▪ Volute casing with integrally cast pump feet
▪ Replaceable casing wear rings (as required)
Impeller type
▪ Closed radial impeller with multiply curved vanes
Shaft seal
▪ Gland packing
▪ Commercial single and double mechanical seals
▪ Commercial cartridge seals
▪ Shaft fitted with a replaceable shaft protecting sleeve in the shaft seal area
Alternative:
▪ Version without shaft protecting sleeve with “wet shaft” (in Europe and
Northern Asia only)
Bearings
Bearings:
▪ Medium-duty
– Radial bearing: cylindrical roller bearing
– Fixed bearing: paired angular contact ball bearings / double-row angular
contact ball bearing
▪ Economy
– Floating bearing assembly: deep groove ball bearings
Lubrication:
▪ Oil lubrication
▪ Grease lubrication

Applications

Handling of aggressive liquids in the chemical and petrochemical
industries as well as in refinery

Overview of technical data

KSB-Mega CPK Configuration
Type of impeller Closed / Radial
Type of installation Long- coupled
Maximum drive rating 90 kW
Impeller material (EN standard) 1. 4593 / 1.4517 / A995GRCD4MC;GP240GH+N/ A216GRWCB;JL1040/ A48CL35
Type of bearing Ball bearings
Drive frequency 50 Hz / 60 Hz
Maximum speed of rotation 4 1/min
Maximum flow rate 1. 160 m³/h
Maximum discharge-side pressure 25 bar
Casing material (EN standard) DUPLEX STAINLESS STEEL 1. 4593/;GREY CAST IRON JL1040 / A48CL3;STAINLESS STEEL 1.4408 / A743;STEEL GP240GH+N/ A216 GR WCB
No. of impeller entries Single entry
Integrated control system Yes
Minimum flow rate 2 m³/h
Suction characteristics Non- priming
Drive voltage Low voltage
Pull-out design Yes
Pump set location Dry installed
Heatable Yes
Max. permissible fluid temperature 400 °C
Main applications Industry and process engineering; Oil / Gas
Type of casing Volute casing
Type of connection Flange
Type of lubrication Grease / Product lubrication
Type of drive Electric motor
Installation position Horizontal
Level indication Grease lubrication
Shaft material (EN standard) ALLOY STEEL 1. 7709+QT+SR;DUPLEX STAINLESS STEEL 1.4462;STEEL C45+N
Type of coupling Direct
Shaft seal type Gland packing; Mechanical seal
Maximum head 162, 00 m
Maximum rated pressure (discharge) PN25
Minimum head 2, 00 m
Nozzle position End suction
Casing partition Radially split

 

EBARA                    GRUNDFOS                     KSB             

EBARA-EVM - VERTICAL MULTI-STAGE STAINLESS STEEL PUMPS

EBARA-EVM – VERTICAL MULTI-STAGE STAINLESS STEEL PUMPS

APPLICATIONS

Ebara-EVM-Series• Civil, Industrial, farming, fire-fighting, boosting systems
• Water treatment plants (reverse osmosis, filtrations)
• Irrigation system
• Washing system
• Movement of hot and cold water for heating, cooling and air-conditioning system.
• Boiler feeding
• Movement of moderately aggressive chemical liquids without solids.

Water treatment

• reverse osmosis systems
• distillation systems
• filtration
• light chemical applications;

 

Industrial washing systems

• car washing, bottle and glassware washing,
parts washing, crate washing, washing and
finishing of metal parts, vegetable washers, and
seafood washing applications
• fire-fighting systems;

Heating and conditioning

• hot water circulation
• cooling systems
• industrial boilers;
Water supply
and pressurization
• pressure boosting
• machine tools;
Agriculture and irrigation

• field irrigation
• sprinkler irrigation
• drip irrigation.

MATERIALS

Ebara-EVM• Impeller, diffusers, casing cover, outer casing, shaft sleeve, coupling covers,
fixing in contact with liquid: AISI 304 stainless steel
• Bottom casing: AISI 304 stainless steel (EVM) – cast iron (EVMG),
AISI 316L (EVML)
• Motor bracket and base: cast iron (not in contact with the pumped liquid)
• Bearings (in contact with liquid): tungsten carbide
• Mechanical seal: Silicon carbide/carbon/Viton
• Shaft: AISI 316 stainless steel
• Tie rods and fixings not contact with liquid: zinc coated stainless steel

CARTRIDGE SHAFT SEAL

EVM 32-45-64 pumps mount the carridge shaft seal
All components of a cartridge shaft seal constitute a sole part on a shaft sleeve. The cartridge mechanical seal is ready to
be installed between pump shaft and motor shaft. The most important benefits of this kind of seal are:
• Easy to install
• Protected seal faces
• Safe and easy handling
We are at disposal for evaluating your specifications and needs in order to find the best solution for your plants and
applications.

MOTORS

• Pumps configured for the installation of a standard IEC motor
• Pumps suitable for different motor types: explosion proof, high efficiency, low noise and with integrated inverter
(EVM VS)
• 50 – 60 Hz
• 2 – 4 poles
• Motors with various voltages and frequencies
• Motors conforming to UL/CSA standards on request.

 

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

EBARA FIRE FIGHTING PUMPS

Features Ebara Fire Fighting Pumps

  • Non Overload design to ensure stable performance for all applications
  • Corrosion resistant materials used on the rotating parts
  • Hydraulically balanced impeller extends bearing life and assures smoother operation
  • Fully compliance to NFPA-20 and certified by Underwriters Laboratories (UL)

 

Specification Ebara Fire Fighting Pumps
  • End Suction Pumps *) Ebara Fire Fighting Pumps

Easy removal and maintenance, BPO (Back Pull Out) system allows all rotating elements to be removed without disconnecting suction and discharge pipe work. Top centreline discharge, foot support under casing for maximum resistance to misalignment and distortion from pipe loads. Flow rate capacity 250 up to 750 USGPM. Working pressure up to 250 psi with 250 lb. ANSI Flanges.

*) UL File Number “EX15585”

  • Horizontal Split-Case Pumps **)

Very compact design for easy of installation and permits minimum maintenance. Axially split casing allows the easy removal of the top casing for inspection and service. Available in horizontal or vertical configuration. Available in clockwise or counter clockwise rotation to simplify pump room layout. Flow rate capacity 500 up to 1250 USGPM. Working pressure up to 250 psi with 250 lb. ANSI Flanges.Ebara Fire Fighting Pumps.

Material
  • Ebara Fire Fighting Pump Casing Ductile cast iron (FCD450) for FSA model; Cast iron (FC250) for CNPA model, Impeller bronze casting (CAC406), Shaft Stainless steel (SUS316), Shaft sleeve Bronze casting (CAC406), Gland packing Teflon (PTFE) impregnate

Grundfos MQ self-priming multistage pump

Grundfos MQ self-priming multistage pump

…much more compact

The Grundfos MQ is a compact all-in-one pressure boosting unit,
designed for domestic water supply and other boosting or lift
applications. The MQ is a compact and reliable, easy-to-install
pump, with many standard features.

The MQ pump is ideal for pressure boosting from water storage
tanks or from city water supply (maximum 45 psi inlet pressure).
The MQ is also a self-priming multistage centrifugal pump. It can
selfprime from a well depth of down to 26 feet within a
maximum time of 5 minutes.*

* For detailed suction lift performance characteristics, refer to
the MQ product guide

 

Grundfos-MQ

 

The Grundfos’ MQ pump is compact and extremely
easy to install. The pressure switch and tank are
already built into the MQ. Furthermore, it is selfpriming
and water-cooled with a very low noise level.
The outlet pipe connection can be angled up to 5° to
fit your existing pipe-work.
Grundfos’ MQ pump is simple and easy to operate.
The settings are clearly indicated on the user-friendly
control panel with indicator lights for Pump on/off,
auto reset, and an alarm indicating dry running or
overheating.
Grundfos MQ is built for trouble-free operation. It’s
construction from corrosion-resistant materials
means it can be used for clean water. The anti-cycling
feature prevents the pump from repeatedly starting
and stopping in the event of a dripping tap or a minor
leak. If there is no water available, the pump will stop
to protect itself and restart automatically when
water is available again

Overview

MQ is a compact water supply system designed for domestic, agricultural and horticultural applications.Applications

The MQ pump is designed for water supply and pressure boosting

  • in private homes
  • in summer houses and weekend cottages
  • on farms
  • in market gardens and other large gardens.

 

The pump is suitable for pumping of potable water and rainwater.

Grundfos-MQ-CurvesPerformance range: Flow up to 20 gpm
Head up to 139 ft
System pressure: Up to 109 psi
Inlet pressure: Max. 45 psi
Suction lift: Max. 26 ft
Liquid temperature: 32°F to +95°F
Ambient temperature: 32°F to +113°F
Nominal voltage range: 1 x 110 – 120 V or
1 x 220 – 240 V
Weight: 29 pounds
Dimensions: 12.6 x 22.4 x 8.7 (in)
Thermal protection Yes

Features and benefits

  • All-in-one pressure booster unit
  • Easy to install
  • Easy to operate
  • Self-priming
  • Dry-running protection
  • Low-noise
  • Maintenance-free.

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

KSB-Amarex KRT - G, G1, G2, GH

Amarex KRT with highly efficient submersible motors

With highly efficient IE3* submersible motors the pumps of the Amarex KRT® series are a true innovation on the market. KSB’s extremely energy-efficient motors can be integrated into pump stations as standard. The pump sets can be supplied with or without explosion protection

Amarex_KRT-EKSB’s in-house development work has enabled these pump sets to be mechanically and electrically optimised for the special requirements of waste water transport. The Amarex KRT motors’ electrical and magnetic design fulfils the requirements of the IE3* efficiency class up to a drive rating of 850 KW.

Combining these motors with a wide range of hydraulic systems for handling waste water enables KSB to provide pump sets offering superb efficiency and dependable operation for every application. Save energy effectively

Design

Vertical, single-stage submersible motor pump in close-coupled design, various impeller types, for wet or dry installation, stationary and transportable version. Design to ATEX.

Applications

Handling of all types of abrasive or aggressive waste water in water and waste water engineering as well as industry, especially untreated sewage containing long fibres and solid substances, fluids containing gas / air, as well as raw, activated and digested sludge; sea water desalination.

 

Pump sets of installation types P and S

KSB-Amarek-KRT-Guide railare designed for continuously submerged operation. The motor is cooled by the fluid
handled on the motor surface. Operation with the motor outside the fluid handled is
possible for short periods.

Pump sets of installation type K

are suitable for continuous operation with the motor outside the fluid. Cooling is
effected by means of air convection.

Operating data

Capacity Q up to 6200 m3/h, 1700 l/s
Head H up to100 m
Motor power P2 from 0,8 kW to 320 kW
Temperature of
pumped liquid t up to 60 oC
Enclosure type IP 68 to EN 60 529 / IEC 529
additional flameproof versions ATEX II 2G T3 or T4

Drive

Three-phase asynchronous motor
400 V (variants: 230 V, 500 V, 690 V)

Material

Standard version of cast iron
Material variants of wear-resistant chilled iron and
corrosion-resistant duplex stainless steel

 

Overview of technical data

Type of bearing Rolling element bearings
Casing partition Radially split
Cutter Yes
Drive frequency 50 Hz / 60 Hz
Type of drive Electric motor
Drive voltage Low voltage
Connection to power supply < 690 V, 3~
Explosion protection ATEX II 2 G T3; ATEX II 2 G T4
Impeller material (EN standard) JN 3029; JL 1040;1.4517
Type of installation Close- coupled
Type of coupling None
Type of lubrication Grease lubrication
Max. permissible fluid temperature 60 °C
Nozzle position End suction
Maximum rated pressure (discharge) PN 16
Pump set location Dry installed; Wet well
Shaft material (EN standard) C45+ N;1.4021
Suction characteristics Non- priming
Type of casing Volute casing
Type of impeller Open; Closed;Multi-vane impeller;Free flow impeller;Radial;Single-vane impeller;Diagonal;Cutter
Type of connection Flange
Casing material (EN standard) 1. 4517;JL 1040;JN 3029
eClass assignment 36410101; 36410103
Free passage 240 mm
Maximum head 120, 00 m
Minimum head 1, 00 m
Installation position Horizontal or vertical
Shaft seal type Mechanical seal
Main applications Energy; Water;Industry and process engineering;Mining / Dredges;Waste water / sewage;Building services
Casing material Cast iron
Maximum discharge-side pressure 12 bar
Maximum drive rating 850 kW
Type of installation 00; Transportable;Stationary
Maximum flow rate 10. 080 m³/h
Minimum flow rate 0, 60 m³/h
Maximum speed of rotation 3. 500 1/min

 

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

 

Ebara-CDX,CDXM- Centrifugal Stainless Steel Pumps

Ebara-CDX, CDXM Series

Stainless steel single impeller centrifugal pumps.
Featuring the one piece volute manufactured using
Ebara’s unique plasma stamping process.

Specifications

˜ Single stage centrifugal pump, closed impeller.
˜ Maximum working pressure: 8 bar
˜ Maximum liquid temperature: 60 °C (for models 70/05-70/07-90/10)
~90 °C (for other models)

Materials

Ebara-CDX-Drawing˜ Pump casing: 304 Stainless Steel
˜ Impeller: 304 Stainless Steel
˜ Casing Cover: 304 Stainless Steel
Shaft: 303 Stainless Steel
˜ Bracket & Motor Frame: Aluminium
˜ Mechanical seal: Carbon/Ceramic/NBR
˜ (wetted part)

Motor Data

˜ TEFC, 2 pole, 50 Hz
˜ Insulation class F
˜ IP55 protection
˜ 1 Phase – 230 Volt
˜ 3 Phase – 230/400 Volt (dual voltage motors)
˜ In built overload protection for 1 Phase

Range

˜ 25 mm Ø discharge
˜ 0.37 to 1.5 kW – 1 Phase
˜ 0.37 to 1.8 kW – 3 Phase
˜ 1.8 m cable with 3 pin plug (1 Phase models only)

Supply

˜ 1.8 m cable with 3 pin plug (1 Phase models only)

Options

˜ High temperature seal (110 °C)
(Carbon/Ceramic/Viton seal, Viton O’ Rings)
˜ Hard faced seal (SiC/SiC/Viton seal, Viton O’ Rings)

Performance Curve

Ebara-CDX-CurveSynchronous
Speed:
3000 rpm

Water temp:
20 °C

Applicable
standard
of test :
ISO 9906
Annex A

Model Code

CDXM 120/12
Motor Size
Nominal Capacity
(70,90,120 or 200 lpm)
Model CDX = 3 Phase
CDXM = 1 Phase
(M ~ Monophase)

 

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

Wilo-JP series-Centrifugal Sanitary Pumps

Product Introduction

Wilo-JP series-Centrifugal Sanitary Pumps in all sectors of beverage and food processing industries,

JP series, special feature with unique spiral-shaped casing and the double curved impeller design for high efficiencyhave proven successfully by absolute reliability such as low energy consumption,

perfect CIP and low noise level.

 

Features / Benefits

Wilo-JP-DIMIdeal for hygienic application of dairy, food, beverage,
pharmaceutical and other industries
Unique spiral-shaped casing for high efficiency
Designed for either CIP or easy manual cleaning
Low NPSH requirement, power consumption, noise level
Up to 100m³/hr flow rate, 80m head
SS316L for all wetted parts & EPDM standard
Single seal standard & easy change to double seal

Wilo-JP-Curves

 

 

 

 

 

 

 

 

 

 

 

 

 

Wilo-JP-Material

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EBARA              GRUNDFOS              KSB             WILO           TSURUMI

EBARA-3-3L SERIES Centrifugal pumps close coupled and standardized

EBARA-3-3L SERIES

Centrifugal pumps close coupled and standardized

Ebara-3-Series

CENTRIFUGAL ELECTRIC PUMPS END SUCTION IN COMPLIANCE WITH EN 733
(FORMER DIN 24255)
End suction centrifugal pumps built in stainless steel AISI 304
(3 Series) and AISI 316L (3L Series)


APPLICATIONS

• Water supply to civil, agricultural and industrial plants
• Pressure boosting
• Fire-fighting, heating systems and air-conditioning
• Moving industrial liquids
• Irrigation
• Refrigeration towers
• Swimming pools
• Emptying
• Washing plants


TECHNICAL DETAILS

Ebara-3-Series-contruction• Can also work in vertical position
• Highly resistant contruction
• Hydroforming process EBARA patent

PUMP TECHNICAL DATA

• Maximum working pressure: 10 bar
• Maximum temperature of the liquid:
-10°C ÷ +90°C
-10°C ÷ +110°C (L-H-HS-HW-HSW-E versions)
-10°C ÷ +120°C (ES version)
• MEI >0,4 for SERIES 3(L) 2 poles, MEI >0,1 for SERIES 3(L) 4 poles
For further information please see our Data Book

MOTOR TECHNICAL DATA

• High efficiency IE2 motors starting from 0,75kW
• Self-ventilated 2 and 4 poles asynchronous motor
• Class of insulation F (B for high temperatures)
• IP 55 protection degree
• 230V ±10%, 50Hz single phase voltage,
three phase voltage 220-240/380-415V ± 5% (up to 0,55kW included), 50Hz for 3(L)M4 SERIES,
three phase voltage 230/400V ±10% (from 0,75kW to 4kW included), 50Hz for 3(L)M4 SERIES,
three phase voltage 230/400V ±10% (up to 4kW included), 50Hz for the other models
three phase voltage 400/690V ±10% (from 5,5kW and over), 50Hz
• Protection is user’s responsibility

MATERIALS

Ebara-3-Series-contruction1 copy• Pump casing and seal housing disc:
– AISI 304 per 3 Series 32-125/160/200
40-125/160/200
50-125/160
65-125/160/200
– AISI 316L for 3L Serie 32-125/160/200
40-125/160/200
50-125/160
65-125/160/200
– AISI 316 microcasted for 3L Series 65-250
80-160/200/250
• Impeller in:
– AISI 304 for 3 Series 32-125/160/200
40-125/160/200
50-125/160
– AISI 316L for 3L Series 32-125/160/200
40-125/160/200
50-125/160
– AISI 316 microcasted for 3 SERIES 65-125/160/200
3L SERIES 65-125/160/200
65-250
80-160/200/250
• Standard mechanical seal:
– Carbon/Ceramic/NBR for 3 Series 32-125/160/200
40-125/160/200
50-125/160
65-125/160/200
– SiC/SiC/FPM for 3L Series 32-125/160/200
40-125/160/200
50-125/160
65-125/160/200/250
80-160/200/250
– Special mechanical available on request

EBARA               GRUNDFOS              KSB              WILO          TSURUMI

Tsurumi-NH-Submersible Wastewater Pumps

 

 

Tsurumi-NH-Submersible Wastewater Pumps

Tsurumi-NH-series is a cast iron made, submersible wastewater pump utilizing 2-pole
motor. This impeller is a shrouded two-channel impeller. Each channel is
designed to have a larger area and it enables the pump to be suitable for
pumping wastewater containing a certain size of solids. The pumps are available in six
motor sizes ranging from 1.5 to 7.5kW and available in either High-Head or High-Volume Type

Tsurumi-NH-Modular

Applications

• Draining wastewater from kitchen at a hotel, restaurant, and
hospital, etc.
• Drainage from factory, underground car park, and basement, etc.
• High-head pumping of wastewater containing solid matters

 

 

 

 

 

 

1. Anti-wicking Cable Entry

An anti-wicking block is provided at the cable entry
Tsurumi-NH-Cablesection of the motor chamber. Even if the cable jacket
becomes damaged or the tip of the cable is accidentally
immersed in water, this device prevents water from traveling
into the motor chamber through capillary action.

2. Motor Protector

A built-in thermal motor protection device reacts to the excessive heat
caused by overcurrent or run-dry conditions. It not only cuts off the
motor circuit automatically but also resets by itself. When the motor
cools down to a safe operating temperature, the motor restarts

3. Dual Inside Mechanical Seal

A mechanical seal with dual seal faces containing silicon carbide (SiC)
is equipped with the oil chamber. As both upper and lower sealing
faces are lubricated by the oil only, it ensures a longer life of the
product and a stable sealing effect.

4. Oil Lifter (Patented)

Tsurumi-NH-OilThe Oil Lifter is a lubricating device that forcibly lubricates the mechanical
seal. It further stabilizes the functions of the mechanical seal and
extends the life expectancy of the seal and also the maintenance term.

5. Air Release Valve

In order to prevent “air lock”, an air release valve is built in the pump
casing. The valve is similar to a ball check valve. When air goes
through the valve, the ball stays at the bottom, but when the pumped
water starts to flow, it closes the outlet by its buoyancy.

6. Seal Pressure Relief Port (5.5 & 7.5kW only)

A small chamber is provided between the oil seal and the shaft hole of
the pump casing, and this chamber is led to the outside by this hole.
With this device, the pumping pressure does not act on the mechanical
seal. The mechanical seal is protected from over rated limit.

 

Guide Rail Fitting System

The guide rail fitting system connects the pump to and
Tsurumi-NH-Guide railfrom the piping easily just by lowering and hoisting the
pump, allowing easy maintenance and inspection without
the need to enter the sump.
The TOS is the standard guide rail fitting system made of
cast iron and is compatible with cast iron pumps.

Accessories

• Duckfoot Bend
• Guide Support
• Guide Hook
• Lifting Chain 5m (with Shackles)
• JIS 10kg/cm2 Flange

 

EBARA               GRUNDFOS                 WILO             TSURUMI

 

Wilo-VeroTwin-DPL-Glanded double pump in in-line design

 

 

 

 

Wilo-VeroTwin-DPL

 

 

Design

Glanded double pump in in-line design with flange connection

Wilo-VeroTwin-DPL

 

Application

For pumping heating water (in accordance with VDI 2035), water-glycol mixtures and cooling and cold water without abrasive substances in heating, cold water and cooling water systems

 

 

 

 

 

 

Special features / product benefits

  • Wilo-VeroTwin-DPL-DimHigh-efficiency motors as standard; from 0.75 kW nominal motor power: motors with IE2 technology
  • Reduction of space required and installation costs due to double pump design
  • Main/standby mode or peak-load operation (by means of external auxiliary device)
  • Standard condensate drainage holes in the motor housings and lanterns
  • High corrosion protection thanks to cataphoretic coating
  • Series version: Motor with one-piece shaft
  • Version N: Standard motor B5 or V1 with stainless steel plug shaft
  • Bidirectional mechanical seal with forced flushing
  • Easy to install thanks to feet with threaded holes on the pump housing for all flange-end pumps

Wilo-VeroTwin-DPL-Curve

 

Technical data

  • Permissible temperature range -20 °C to +120 °C
  • Mains connection 3~400 V, 50 Hz (others on request)
  • Protection class IP 55
  • Nominal diameter DN 32 to DN 100
  • Max. operating pressure 10 bar (special version: 16 bar)

 

 

 

EBARA               GRUNDFOS              KSB              WILO          TSURUMI

Pages:1234...1920Next »