Shimge Vertical Multi-Stage Centrifugal Pumps BL

Description

BL(T) series stainless steel multi-stage centrifugal pump (afterwards called pump)boasts characters of high efficiency, low noise, steady operation, etc.The pump set adopts the non-self-priming vertical multi-stage structure, which makes a compact whole,its installation easy, its operation and maintenance convenient.

Application Limits

  • Medium temperature: normal type:0℃ ~68℃ hot water type:0℃ ~120℃,
  • Ambient temperature:+40℃ ,
  • Max ambient pressure:1.0MPa,
  • Advisable to use motor of higher power in case that the density or viscosity of medium is above that of water.
  • PH: 5 to 8
Applications Fields 

Water supply BL BLT
Filtration and transfer at waterworks
Distribution from waterworks
Pressureboosting in mains
Pressure boosting in high-rise buildins,hotels,etc.
Pressure boosting for industrial water supply
Industry
Pressure boosting
Process water systems
Washing and cleaning systems
Vehicle washing tunnels
Fire fighting systems
Liquid transfer
Cooling and air-conditioning systems(refrigerants)
Boiler feed and condensate systems
Machine tools(cooling lubricants)
Aquafarming
Transfer
Oil and alcohol
Glycol and coolants
Water treatment
Ultra-filtration systems
Reverse osmosis systems
Softening, ionising, demineralizing systems
Distillation sys tems
Separators
Swimming baths
lrrigation
Field irrigation(flooding)
Sprinkler irrigation
Drip-feed irrigation

 

Certificate

Electric Motor

Full-enclosed and ventilating two-pole standard motor
Protection clsas: IP55
Insulation class: F
Standard voltage Single phase 220V-50Hz Three phase:380/400V-50Hz

Energy Efficiency Standard (IEC60034)

Calculation Of minimum Inlet Pressure

If the pressure in pump is lower than the vapour pressure of medium, cavitation will occur, which will affect the performance of pump. To avoid the cavitation and ensure the pump inlet has a minimum pressure, maximum suction head should be calculated as following:

H=Pbx10.2-NPSH-Hf-hv-Hs

Pb: Atmospheric pressure, bar (In close pipeline system, it can be considered as the system pressure );
NPSH: Net positive suction head, m (Value at maximum flow of Q-NPSH curve);
Hf: Suction pipe line loss (Value at maximum flow of corresponding pipeline);
Hv: Medium vapour pressure, m (Medium vapour pressure at corresponding temperature, the default medium is water, as shown in figure4 on the right );
Hs: Safety margin, m, general value is 0.5.
Calculation result: if H is positive, the pump is installed in suction way, otherwise, it is installed in downdraft way.

Note: It is not necessary to do above calculation under general conditions. Only when we use pump in the following situations do we need to calculate the H:
1. Medium temperature is high;
2.The velocity of flow is larger than rated value;
3.Suction head is big or inlet pipeline is long;
4.System pressure is small;
5.Inlet condition is bad.

Selection Of Pumps

Selection of pumps should be based on:
Duty point of the pump.
Dimensional data such as pressure loss as aresult of height differences,friction loss in the pipework,
Pump efficiency etc.
Pump materials
Pump connections
Commonly used mechanical seal configuration tables

1. Duty point of the pump:

From a duty point it is possible to select a pump on the basis of the curve charts shown in “performance curves/technical” data.

2. Dimensional data:

When sizing a pump the following must be taken into accounting: •Required flow and pressure at the draw-off point. •Pressure loss as a result of height differences. •Friction loss in the pipework(Hf) (Refer to Fig.1) It may. •Best efficiency at the estimated duty point. •NPSH value. •For calculation of the NPSH value, see corresponding curves chart.

3. Pump efficiency:

Before determining the best efficiency point, the operation pattern of the pump needs to be identified. If the pump expected to operate as the same duty point, then select a BL pump which is operating at a duty point corresponding with the best efficiency of the pump.
As the pump is sized on the basis of the highest possible flow, it is important always to have the duty point to the right on the efficiency curve(eta) in order to keep efficiency high when the flow drops.

4. Pump material:

Selection of pump connection depend on the rated pressure and pipe work. the pump offer a wide range of ftexible connection such as:

5. Commonly used mechanical seal configuration tables

Application Field Shaft seal type Shaft seal material
Normal Special 1 2 3
4
5
Type key
Rotating part Code Stationary part Code Elastomers Code Compression spring Collor Code
0℃ to +90℃ clean water Graphite A SiC S FPM F SUS304 C ASFC
0℃ to +90℃ clean water WC W Graphite A FPM F SUS304 C WAFC
+90℃ to +120℃ corrosion resistance SiC S SiC S EPDM E SUS304 C SSEC
up to 0℃ WC W WC W EPDM E SUS304 C WWEC
Mechanical seal type Pump model d1 d2 h
NJK BL(T)2/4 12 12 55
BL(T)8/12/16/20 16 16 57.5
BL(T)32/45/60/90 22 22 72
NDA BW(J)2/4 12.7 16 32
BW(J)8/16 17.4 20 33.5
Maximum Work Pressure 

Model Curve No.
BL(T)2,4 2
BL(T)8,12,16,20 3
BL(T)32-2-2~BL(T)32-7 1
BL(T)32-8-2~BL(T)32-12 4
BL(T)32-13~BL(T)32-15-2 5
BL(T)45-2-2~BL(T)45-6 1
BL(T)45-7-2~BL(T)45-9 4
BL(T)45-10-2~BL(T)45-13-2 5
BL(T)64-2-2~BL(T)64-5-2 1
BL(T)64-5-1~BL(T)64-8 4
BL(T)90-2-2~BL(T)90-4-2 1
BL(T)90-4~BL(T)90-6 4
BL(T)120,150 6

 


The limits of pressure and temperature are shown in the following fig.4,the pressure and temperature must be in the shown in the fig. 4.

Maximum Ambient TemperatureWhen the pump is operating in the place where ambient temperature is higher than 40℃ or altitude is higher than 1000m,the output power of motor P2 will decrease because of poor cooling caused by low air density.Therefore, in that case,the pump should be equipped with high-power motor.

Performance Range

Product Range

Performance Curve – BL(T)2

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)4

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)8

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)12

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)16

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)20

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)32

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)45

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)64

It is recommended to be used within lift range.

Performance Table

PN25-40/DN100 standard flange, on request.

Performance Curve – BL(T)90

It is recommended to be used within lift range.

Performance Table

PN25-40/DN100 standard flange, on request.

Performance Curve – BL(T)120

It is recommended to be used within lift range.

Performance Table

Performance Curve – BL(T)150

It is recommended to be used within lift range.

Performance Table

Components & Materials

Packing Sizes & Weight

Hot Tags: Vertical Multi-Stage Centrifugal Pumps BL, China, Manufacturers, Suppliers, For Sale, Companies, Best, Price, Buy, High Quality